Posted in

How to cut an empty beverage can safely?

Hey everyone, it’s Jake here from your go-to beverage can supplier—you know, the one that’s got your back when you need reliable cans, fast. Today I’m chatting about something I get asked all the time by folks who come into our warehouse, slide into our DMs, or even hit us up at trade shows: “Wait, how do I cut an empty beverage can safely?” Beverage Can

I get it. Maybe you wanna turn old soda or energy drink cans into planters, keychains, that weird tiny side table someone’s always posting on TikTok, or just get a clean, straight cut for a DIY project. But let’s be real—messing up a can cut (or not using the right tools) is a surefire way to end up with a tiny metal shard in your finger, a cut that bleeds more than your morning coffee, or even a ruined good can if you weren’t just repurposing.

As a can supplier, I’ve seen everything from people using a random kitchen knife (bad, just bad) to those who try to twist a pair of rusty scissors (also bad) and wonder why their cut’s jagged and full of burrs. So let’s break this down like I’m explaining it to a buddy who’s never held a rotary cutter before—no fancy jargon, no overcomplicating, just the actual science and safe steps I’ve picked up (plus a few lessons from when a new warehouse intern tried this last year and nicked their thumb).

First, let’s talk about why empty cans are actually tricky to cut, even when they’re totally empty. You’d think “empty” means it’s just metal, right? Nah. Most standard beverage cans (the 12oz ones you grab at gas stations, the 16oz hard seltzer cans, even the big 24oz ones) are made from either aluminum (most common) or tin-plated steel (think older soda cans, some craft beer ones). Both are thin, but they’re also super malleable—meaning they bend way easier than they slice through cleanly, and those sharp little edges that stick out after a bad cut? Those are the burrs we’re gonna avoid like the plague.

Also, even if you rinsed the can out with a half dozen times, there’s still gonna be residual gunk—sugary soda, coffee, whatever—trapped in the seams. That stuff isn’t dangerous, but it can make the can slippery while you’re cutting, which is another recipe for injury. So step one before you even touch a tool: Prep your can. Don’t skip this. It takes 2 minutes and saves you a trip to the urgent care.

Prep step 1: Rinse it out. Hot water, dish soap, scrub the inside with a bottle brush or even a dish sponge. Pay extra attention to the bottom and the top rim—those are the spots where liquid hangs out. If you’re gonna cut the whole can in half, maybe let it soak for 10 minutes to get any crusty sugar off. Step 2: Dry it COMPLETELY. Damp metal is slippery, and if you’re using a tool like a rotary cutter, moisture can mess with the blade too. Pat it with a towel, even blow it out with a hair dryer if you’re in a hurry. Step 3: Remove any labels or plastic liners. Labels get sticky when wet, they’ll make the can slide, and the plastic is just extra stuff in your way. Peel ’em off (use a little warm water if they refuse to come up) and wipe the can down one last time.

Now, let’s talk tools. This is where most people go wrong. You don’t need a $100 metal cutting kit, and you definitely don’t need to use your mom’s kitchen shears (she’ll kill you if you mess those up). I’ve tested every single tool for this—both in my home workshop and with our team’s DIY projects—and the best ones are:

First, for straight cuts (like cutting the top off to make a planter, or slicing the can in half): A rotary tool with a metal cutting wheel, or a utility knife with a fresh, sharp blade. Wait, hold up—sharp is key. A dull knife is way more dangerous than a sharp one, because you have to press harder, and it slips. If you’re going the utility knife route, make sure the blade is extended all the way, and replace it if it’s been used for anything else (like cardboard). For curved cuts (like making a small can lantern, or a custom shape): A pair of heavy-duty tin snips (the ones specifically for metal, not paper or fabric) or a small coping saw with a metal blade. And for total newbies who don’t wanna risk cutting themselves? There are actual can cutting tools—little hand-held things that clamp to the rim and spin, making a perfect circle. I keep one of these in my work bag for quick projects, honestly.

Wait, but hold on—even with the right tool, there’s a safe way to hold the can. Let’s get that out of the way first, because I’ve seen people hold the can like a little club and wonder why it’s spinning around mid-cut. If you’re doing a straight cut, lay the can flat on a stable surface (a workbench, a cutting board, even a thick table—nothing wobbly). If you’re cutting a circle (like the top off), you can hold it in one hand, but keep the other hand curled under the can so your fingers aren’t near the path of the blade. No loose sleeves, no dangly jewelry—those can catch on the tool or the can, leading to a bad time.

Now, let’s get to the actual steps, depending on what you’re cutting. Let’s start with the most common request: Cutting a standard 12oz aluminum can in half, for a planter or a DIY cup. This is what most people want, so let’s nail this.

Step 1: Mark your cut line. Use a ruler and a permanent marker to draw a straight, even line around the can. Don’t eyeball it—you’ll end up with a lopsided cut, and that’s just annoying. Make the line dark so you can see it clearly. If you’re cutting the top off (like to make a little pot), mark it ½ to 1 inch below the top rim. That way you have a smooth edge to work with, and you’re not cutting too close to the sharp original rim.

Step 2: Secure the can. If you’re using a utility knife or rotary tool, lay it flat on your work surface, with the marked line facing up. You can tape the edge of the can to the workbench with a little masking tape to keep it from spinning. Super important—no movement mid-cut.

Step 3: Start cutting. If you’re using a utility knife: Hold the knife at a 45-degree angle to the can. Score the line first—don’t push all the way through the metal on the first pass. Go around the line 3 or 4 times, applying a little more pressure each time, until you cut all the way through. If you rush and push too hard on the first pass, the knife will slip and you’ll cut your hand. If you’re using a rotary tool: Attach the metal cutting wheel, put on safety glasses (I cannot stress this enough—metal shavings fly everywhere), turn it on, and slowly run the wheel along the marked line. Don’t press hard—let the tool do the work. You don’t need to muscle it, and pressing too hard will cause burrs.

Step 4: Deburr the edge. This is non-negotiable. The cut is done, but the edge is super sharp—like, sharp enough to slice paper. Take a piece of fine-grit sandpaper (220 grit works perfect) and rub it back and forth along the cut edge for 30 seconds. If you’re fancy, you can use a metal file, but sandpaper is way easier for beginners. Run your finger along the edge (gently!) to make sure there are no sharp spots. If it feels even, you’re good. If not, sand a little more.

Wait, what if you’re using tin snips for curved cuts or smaller projects? Let’s go over that. Tin snips are great if you don’t have a rotary tool, and they’re way cheaper than buying one. The key here is using the right snips: Left-cut, right-cut, or straight-cut snips. For most small curves, straight-cut snips work fine, but if you’re making a tight curve, use left or right-cut snips to follow the line. Mark your line first, just like before, hold the can firmly, and snip along the line slowly. Don’t snip too fast—you’ll bend the metal and get a jagged edge. After you’re done, deburr the edge too—snips leave their own sharp little nicks, so sand that edge down.

Now, I need to talk about safety. This is the part that can’t be skipped, because I’ve seen way too many people ignore this and end up hurt. First, ALWAYS wear safety glasses. Metal shavings go flying when you cut a can, and if one gets in your eye, that’s a hospital trip no one wants. Second, gloves—work gloves, not those thin latex ones. The gloves will protect your hands from sharp edges while you’re holding the can, and also from any metal shavings. Third, no bare hands near the blade, obviously. Keep your fingers at least an inch away from the path of the tool. And if you’re using a power tool (rotary tool, coping saw), keep it away from water, and don’t leave it plugged in when you’re not using it.

Wait, what about empty cans that still have pressure? No, right? Even if you uncrinkled the top, there’s no pressure in a sealed empty can—once a can is open, the pressure’s gone. The only time you’d have pressure is if you left it sealed but empty, which is super rare. So don’t worry about the can exploding when you cut it— I’ve cut thousands of these at our warehouse, and I’ve never had one pop. The only exception is if it’s a sealed soda can, but we’re talking about empty ones, so you’re good.

Also, let’s talk about mistakes to avoid. Number one: Using a kitchen knife. I’ve done this once, when I was 16 and trying to make a can keychain. The knife slipped, cut my palm, and I had to get 2 stitches. Don’t be like 16-year-old me. Number two: Dull blades. Like I said earlier, dull blades make you push harder, which leads to slips. Change your knife blade or sharpen your tin snips before you start. Number three: Not deburring. I made a planter last year for my mom’s herbs, skipped the sanding step, and her finger got sliced when she tried to repot a plant. She still teases me about it. Don’t do that. Number four: Cutting too fast. Take your time. This isn’t a race—10 minutes of safe cutting is way better than 1 minute of rushing and getting hurt.

Now, since I’m a beverage can supplier, I have to mention something here. If you’re doing this regularly—like, if you’re a crafter who makes can planters or jewelry to sell, or a small business that needs custom cut cans for packaging—using high-quality, food-grade empty cans (wait, no, empty ones are still food-grade if they’re not contaminated) is important. Bad, flimsy cans will bend while you’re cutting, leading to uneven edges and more slips. All the cans we supply are made from sturdy, consistent aluminum or steel, so they cut cleanly every time, no warping mid-project. Just saying, if you’re going to invest time in DIY, why not use a good can?

Wait, let’s do a quick recap for anyone who skimmed this:

  1. Prep your can: Rinse, dry, remove labels. 2. Pick the right tool: Utility knife (fresh blade), rotary tool with metal wheel, tin snips, or hand can cutter. 3. Mark your cut line with a ruler—don’t eyeball. 4. Hold the can steady, wear safety glasses and gloves. 5. Cut slowly, score multiple times if using a knife. 6. Deburr the edge with sandpaper. 7. Admire your DIY, no trips to the ER needed.

Oh, and one last pro tip: If you’re making multiple cuts for projects, sand all edges at the same time instead of doing it one by one. It saves time, and you get a consistent edge on all your pieces. I’ve got a whole bin of sanded can pieces for our store’s DIY section, and that trick cut my prep time in half.

Look, I know cutting an empty can sounds like a super simple task, but it’s way easier to mess up than you think. As someone who works with cans every single day, I’ve got the scars (metaphorical, mostly) to prove that. But follow these steps, take it slow, and you’ll have a clean, safe cut every time—no cuts, no bent metal, no chaos.

If you’re someone who’s looking for reliable, high-quality beverage cans for your projects, whether big or small, hit us up. We’ve got all sizes, from 8oz mini cans to 24oz tallboys, and they’re perfect for DIY, packaging, whatever you need. Shoot us a message to chat procurement, tell us what you’re working on, and we’ll hook you up.

Metal Can Lids References:

  1. Occupational Safety and Health Administration (OSHA). "Hazard Identification: Metalworking." U.S. Department of Labor, 2023.
  2. American National Standards Institute (ANSI). "Safety Requirements for Metal Cutting Tools." ANSI, 2022.
  3. Aluminum Association. "Properties and Uses of Beverage Can Aluminum." Aluminum Association, 2021.
  4. Tin Plate Technology Association. "Tin-Plated Steel for Food Packaging and DIY Applications." Tin Plate Technology Association, 2020.

Xiamen Uniteam Sourcing Co., Ltd.
As one of the most experienced beverage can manufacturers and suppliers in China, we also support customized service. Please feel free to buy high-grade beverage can made in China here from our factory. Quality products and reasonable price are available.
Address: ROOM 1511, NO. 939, XIAHE ROAD, SIMING DISTRICT, XIAMEN, FUJIAN, CHINA.
E-mail: operator@minjiapack.com
WebSite: https://www.minjia-packing.com/